vastcyprus.blogg.se

1. 2010 VW CC CHECK ENGINE LIGHT HOW TO
2. 2010 VW CC CHECK ENGINE LIGHT DRIVER
3. 2010 VW CC CHECK ENGINE LIGHT PC

Flashing Check Engine Light: If your check engine light is flashing, stop driving your CC and have it towed to your nearest mechanic – a blinking check engine light means you probably have a very serious problem with your car and you risk ruining your engine by driving it. Steady Check Engine Light: If your check engine light is on every time you operate your CC, you need to have it checked as soon as possible, especially if you notice performance problems or unusual noises. For example, does it happen when you accelerating, driving on the highway or does it appear at low speeds? This will help your mechanic evaluate the issue. Is it OK to drive with a check engine light on? Intermittent Check Engine Light: If the check engine light on your 2010 CC is not steady, try to take note of the conditions when this happens.

2010 VW CC CHECK ENGINE LIGHT HOW TO

The video above shows how to locate the on board diagnostics OBD plug location on your 2010 CC, how to read the trouble codes and how to reset or clear the check engine light using a scanner on your CC. Whereas a steady check engine light may mean you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light. If you have a flashing check engine light, turn off the engine immediately to prevent potential motor damage. I have checked the instrument cluster itself and didn't find any sign of specific action done.A check engine light can indicate a broad spectrum of problems with your 2010 Volkswagen CC. May be some smart guy made a trick to make the light dead instead of solving the problem with pretentioneers ? All other lights come on when I put the key on. I do not believe that it could be the burnt LED. What do you suggest to check further to find the reason of the problem.

2010 VW CC CHECK ENGINE LIGHT PC

But the diode on the pc board of the cluster does not come on. The signal on this wire gets about 5V DC when I turn the key to on. I checked the wire from srs module to instrument cluster: it is OK. I put a plastic streaps into the slots to isolate the shorting contacts and now the srs module get proper resistance of the pretensioneers. The problem was that the pretentioneers plugs were disconnected by somebody and black protecting detailes were lost, so the srs module gave codes that there was short circuit in pretentioneers. There was an old problem with seat belts pretensioneers connection which was already solved and the srs ECU gives no codes now. The problem I have is concerned with the srs warning light which never comes on even when I turn the key to on position. How to Reset Tire Pressure Light (TPMS) – By Car Modelįind more information in our list of all car dashboard symbols.How to Disconnect a Car Battery (7 Easy Steps).Is It Safe to Drive With the Airbag Light On? (& Why Not).If you feel that you don’t have the knowledge to work on airbag systems, take it to a mechanic and have them run a diagnostic test. You may understand the safety importance when working on airbags or SRS systems in a car. Now you know how to handle the airbag light. You should never attempt to reset the airbag light without correcting the problem first, because this could cause the airbags to deploy. If you clear the codes, but the airbag light keeps coming back on, there is a problem that needs to be fixed first. In most modern cars, there is no way to reset the airbag light without a scanner. The reset an airbag or SRS light, you need to use a diagnostic scanner to clear the codes after you repair the issue. However, this energy is often drained within minutes. Airbag systems have large capacitors that will store energy in the system for a while even if you remove the battery cable. If you can not find any problems there, you should really get an OBD2 scanner or let a workshop read the codes otherwise, you will just guess the problem out of the dark. Spray the connector plugs with an electronic cleaner and restart your car.

2010 VW CC CHECK ENGINE LIGHT DRIVER

In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals.Ĭheck the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem. This is for safety cautions because you should always repair the fault after the airbag light occurred. It is impossible in most car models to reset the airbag light without a scanner. How to reset airbag light without a Scanner

If the problem comes back, reread the codes and continue the procedure. If the airbag light is gone after a test drive, there is a big chance that the problem is solved. If the airbag light seems to have gone away from your dashboard – restart your ignition and go for a test drive.